Other

• Delivery Time: READY STOCK

• Delivery Time: READY STOCK

MODEL-B&R-POWERPANEL 400 

• Delivery Time: READY STOCK

SIEMENS PLC MODULE EM231 (6ES7231-0HC22-0XA0)  

Siemens 6ES7 231-0HC22-0XA0 SIMATIC S7-200 EM 231 Analog Voltage Input Module for S7-22x CPU only, 4 x Inputs (0-10V DC), 12-Bit Converter ANALOG INPUT MODULE4 POINTANALOG0-10 VDC12 BIT CONVERTER

• Delivery Time: READY STOCK

CLIPSAL 8 CHANNEL DIMMER C BUS 2

Dimmers

The DIN Rail Series Dimmers are C-Bus output units suitable for dimming incandescent & low voltage lighting. For ease of installation the units are DIN rail mounted measuring 12M wide. All units in the series incorporate the C-Bus 'Learn Mode' feature. Learn mode allows the units to be programmed without the need for a PC connected to the system. Alternatively, the units can be programmed via a PC using the installation software.

The 4 channel and 8 channel non universal dimmers feature four or eight leading edge phase controlled dimming channels .

 

The 4 channel dimmer has a load rating of 2 Amps per channel and the 8 channel dimmer has a load rating of 1 Amp per channel. Both dimmers are capable of controlling incandescent lighting and low voltage lighting (utilizing iron-core transformers and electronic transformers compatible with leading edge dimmers).

The 4 channel universal dimmer has a load rating of 2.5 Amps per channel, supports leading & trailing edge dimming and has the ability to report failure of the channel to a suitable error reporting receiver such as the Schedule Plus software.

The type of dimming required will automatically be detected and the channels configured accordingly.

C-Bus connections are conveniently achieved at the unit through the use of RJ45 connectors, allowing similar units to be quickly looped together.

Two variants of each product are available, one incorporating a 200mA C-Bus power supply used to source current to the C-Bus network and the other model with the same features and performance, but excluding the 200mA power supply.

During normal operation the units consume no current from the C-Bus network.

This series of units are capable of generating a C-Bus clock signal and providing a C-Bus network burden. Both the clock signal and the burden are selectable through the C-Bus Installation software.

Local toggle buttons have been included to allow individual channels to be toggled at each unit as well as via C-Bus commands.

Remote ON and OFF facilities are available, permitting all channels to be turned ON and OFF without C-Bus Network communication.

• Delivery Time: READY STOCK

MITSUBISHI RTD INPUT MODULE MELSEC-Q64RD 
Input: 4 channels.
Platinum resistance (Pt10; JPt100).
Conversion speed: 40ms/1.
Channel 18 point terminal.
Platinum thermal resistance (Pt100, JPt100).
Nickel thermal resistance (Ni100).
Shedding detection function.
Conversion speed: 320ms/8 channel.
Inter channel isolation.
40 pin connector.
Most suitable for process control of isolated analog modules.
Temperature data can be collected by connecting thermocouple / thermal resistance.
Products can choose multi-channel (8 channel) input type and channel isolation type.
Customers can choose the most suitable model according to the intended use.
Reduce system downtime recovery time.
With a simple operation, you can back up all the data in the CPU to the memory card.
Through regular backup, can be the latest parameters, procedures, etc. to save the storage card.
In the event of a CPU failure, after the replacement of CPU, can be a simple operation,
Restore the system by using the data storage card in advance.
Therefore, it is not necessary to spend time to manage the backup data, but also can shorten the recovery time of the system shutdown.
Auto backup key data
Save the program and parameter files automatically to the program memory (ROM Flash) without using the backup battery,
To prevent the loss of the program and the parameters due to forgetting to replace the battery.
In addition, the soft component data and other important data can be backed up to the standard ROM,
In order to avoid during the long holiday and other planned downtime,
The data is lost due to battery depletion.
The next time the power is turned on, the backup data will be automatically restored.

BASE UNIT PILZ PNOZ M1P 

Features:

Can be configured in the PNOZmulti Configurator

Positive-guided relay outputs: – 2 safety outputs Depending on the application, up to PL e of EN ISO 13849-1 and up to SIL CL 3 of EN IEC 62061

Semiconductor outputs: – 4 safety outputs Depending on the application, up to PL e of EN ISO 13849-1 and up to SIL CL 3 of EN IEC 62061, – 1 output for standard applications

4 test pulse outputs

1 cascading input and output; can also be used as a standard output

20 inputs for connecting, for example: – E-STOP pushbuttons, – Two-hand pushbuttons, – Safety gate limit switches, – Start buttons, – Light beam devices, – Scanners, – Enabling switches, – PSEN, – Operating mode selector switches, – Safety mats

Muting function Overview Operating Manual PNOZ m1p (ETH) 20878-EN-15 8

LED indicator for: – Diagnostics, – Supply voltage, – Output circuits, – Input circuits

Test pulse outputs used to monitor shorts across the inputs

Monitoring of shorts between the safety outputs

Expansion modules can be connected

Integrated interfaces: – PNOZ m1p: Serial interface RS232, – PNOZ m1p ETH: 2 Ethernet interfaces

Plug-in connection terminals: either spring-loaded terminal or screw terminal available as an accessory

Coated version: Increased environmental requirements

• Delivery Time: READY STOCK

WAGO ANALOG INPUT MODULE 750-459

This analog input module processes standard 0–10 V signals.

The input signal is electrically isolated and is transmitted with a resolution of 12 bits.

The internal system supply powers the module 

The input channels of the module have a common ground potential.

• Item Code: PES202100052

SIEMENS PLC MODULE CPU317-2DP (6ES7917-2AJ10-0ABO) 

6ES7317-2AJ10-0AB0 | Siemens SIMATIC S7-300 CPU 317-2DP

General information Hardware product version 01 Firmware version V2.6 Engineering with Programming package STEP 7 V5.2 + SP1 or higher with HW update Supply voltage 24 V DC Yes permissible range, lower limit (DC) 20.4 V permissible range, upper limit (DC) 28.8 V External protection for supply cables (recommendation) 2 A min. Input current Current consumption (rated value) 850 mA Current consumption (in no-load operation), typ. 100 mA Inrush current, typ. 2.5 A I²t 1 A²·s

• Delivery Time: READY STOCK

ABB ANALOG IO MODULE AX522 B4   

We at Quality Services provides Best-in-class Electronic Repairs & Service for  ABB MAKE ANALOG INPUT MODULE AX522 B4 1SAP250000R001. We also provide free quotation for Repairs & Service of  ABB MAKE ANALOG INPUT MODULE AX522 B4 1SAP250000R001 . We also provide free quotation for all the items sent to us at our works .At Quality Services, we have the best experience in Servicing of ABB MAKE ANALOG INPUT MODULE AX522 B4 1SAP250000R001   in the most economical and cost efficient manner. We are continually updating and improving our capabilities.

Our service centre offer the latest, advanced repairing & testing systems for ABB MAKE ANALOG INPUT MODULE AX522 B4 1SAP250000R001 . The objective of our company is to ensure fast turnaround time competitive pricing & quality repairs.

We believe in strong warranty policy and effective quality assurance. We provide Six months of Service warranty on the repaired product / replaced part for ABB MAKE ANALOG INPUT MODULE AX522 B4 1SAP250000R001 .We also supply imported parts for ABB MAKE ANALOG INPUT MODULE AX522 B4 1SAP250000R001.

We also provide Emergency Onsite/ Offsite Repairs for ABB MAKE ANALOG INPUT MODULE AX522 B4 1SAP250000R001 and similar categories of Electronics.

We at Quality Services provide a total repair solution for all types of Electronics, Instrumentation & Electrical Equipments in all over India. Our main focus is on equipment repairing, maintenance and servicing for companies.

• Delivery Time: READY STOCK

SCHNEIDER BASE UNIT TWDLMD440DTK 

• Description: extendable PLC base Twido 24 V - 24 I 24 V DC - 16 O solid state
• Range of product: Twido
• IP degree of protection: IP20
• Operating altitude: 0...6561.68 ft. (0...2000 m)
• Vibration resistance: 0.075 mm, 10...57 Hz mounting on: 35 mm symmetrical DIN rail, 1 gn, 57...150 Hz mounting on: 35 mm symmetrical DIN rail, 1.6 mm, 2...25 Hz mounting on: plate or panel with fixing kit, 4 gn, 25...100 Hz mounting on: plate or panel with fixing kit
• Shock resistance: 15 gn 11 ms
• Insulation resistance: > 10 MOhm at 500 V, between I/O and earth terminals, > 10 MOhm at 500 V, between supply and earth terminals
• [Us] rated supply voltage: 24 V DC
• Relative humidity: 30...95 % without condensation
• Protection type: Power protection with internal fuse
• Response time: 300 s for Q0.2 to Q0.7 at state 0, 300 s for Q0.2 to Q0.7 at state 1, 5 s for Q0.0 to Q0.1 at state 0, 5 s for Q0.0 to Q0.1 at state 1

• Delivery Time: READY STOCK

MITSUBISHI ISOLATED A-D CONVERTER UNIT MELSEC-Q68AD-G  
Mitsubishi high-precision sequencer that further opens up the possibility of control with intelligent functionality.
[Features]
· Supports process control needs.
· A group of analog units that can handle high-speed/high-precision controls.
[Applications]
· Convenient for supporting process control of general-use sequencers.

• Delivery Time: READY STOCK

MODEL- PROFACE AGP3300-S1-D24
Warning:
Do Not conect/disconnect equipment unless area is known to be nonhazardous or the power has been switched off. Ports "EXT","USB" and 'CF Card' are for system set-up diagnostics in a non hazardous location area only.
For use on a flat surface of a Type 4X(Indoor Use Only) and/or Type 13 Enclosure.

MODEL- TELEMECANIQUE MAGELIS XBTR411

Model-smps murr emparro (87439) 48v dc, 10 a

• Delivery Time: READY STOCK

MODEL-SMPS BAUMULLER BUC625-55-64-005  

• Delivery Time: READY STOCK

MODEL-SMPS PHOENIX CONTACT QUINT-20 (415V AC,24V, 20AMP)